Keshe台灣凱史知識尋求資料館 - 繁體中文 (非官方組織 /官方資料)

#再談優質奈米塗層
精彩了，這個版本跟Sandor的又不一樣了…..

#凱史夫人推薦的奈米塗層法
(#原貼文者RickHarris)

#如何製作奈米物料：穿防護服（護目鏡，口罩(面罩)）避免吸入蒸氣......一旦完成，不要徒手觸碰塗層材料......戴上2-3層一次性使用的橡膠手套。如果你觸碰到奈米材料（使用芸香(ruta)，是一種天然草藥，或是買它的滴劑100ml滴管裝）

#步驟1：將生鏽的鐵釘，鐵絲網，線（實心銅線）放到塑膠容器。

#步驟2：加入苛鹼（可以是結晶體，顆粒，薄片，氨水，氫氧化鈉，鹼液等等）（約一公斤苛鹼可以產生大約半噸的比例材料）（加1/4杯到塑膠容器底部）。

#步驟3：加入沸水(足夠覆蓋材料再高約半英寸/英寸左右，因為你需要一個熱能(也就是沸水)，沸騰的狀態。才能產生對的條件與環境以製造奈米氧化物。

#步驟4：你必須封閉容器的縫隙 (也就是蓋上蓋子)，至少放在那裏24小時。 材料需要時間自行完成工作。24小時後清空容器，盡量不要觸碰到這些材料。你可以倒光容器裡頭的液體.，換到新容器。放一點點苛鹼，加上原來容器的苛鹼液。必須保持有點濕氣。當你再換容器時，你可以用不同材質的容器，會有不同的效果，比方，如果你改換到玻璃容器，不再放到塑膠的。大家比較建議用塑膠的，因為會得到某些效果。

#步驟5：將放置至少24小時容器裡的材料，轉移到另一個導電的容器裡（裡頭有第一個容器的少少量苛鹼液保持一點濕氣，鐵絲網鋪在底部架高約1英吋(2.54公分)。鋪陳這些材料讓它們有充分空間不彼此碰撞，很像烤披薩在傳送帶烤箱一樣。(你會用迷你金屬板/桌子取代鐵絲網讓它與底部保持個距離）

#步驟6：在材料加很小的電壓......同時碰到一塊金屬片和一根鐵釘（鐵釘和金屬片彼此沒有實體接觸），一個電壓表和鱷魚夾（你可以用電池）隨機脈衝5-10秒之間，然後收回電流/電壓。

#步驟7：把蓋子蓋回去（這時是第二個容器），放在那裡至少5-7小時。然後再產生小電流；再次放在那裏5-7小時。24小時內，這個過程重複3或4次。即使是小電池（如上所述）也會產生對的條件讓電流流過。這個過程會讓奈米塗層從底部往上建立起來。

#幾乎零成本做出奈米材料。#奈米材料可以用來清汙染。是一種生產奈米材料很簡單平價的的方式，這個方法已經用了7年，而且用在不同的目的。

#步驟8：這些材料可以移入另一個容器，蓋上蓋子保持密閉直到你要到的時候。所以這是第三個容器請保持密閉，直到你要用為止。

#小撇步，不可將材料接觸到空氣避免進一步氧化。

任何金屬都可以奈米塗層......不管是鋼，鐵，銅，金等等。

銅片（薄得像紙）與氧化銅奈米塗層用在電池。(省很多錢) 可以用來做超導體與絕緣體。

你要記住，你加到鍋子裡的金屬（第一個塑膠容器）會給你不同的複合層....例如，第一次你加鋁（或蠟燭罐）這些會溶解在苛鹼液，給你一個複合塗層。這個複合塗層會由鍋子裡有哪些金屬決定。相較於你專注使用銅。不管怎樣都好，只是結果不一樣....

某個程度，凱史先生說 #奈米塗層像在做磁鐵......看你的塗層是什麼，就吸引到不同的東西。(註: 這是幾年前的貼文。後來的教學提到醫療目的的塗層，勿使用到鋁)

步驟1-8可重複多次，建立出奈米塗層，可再加一些鹽的替代品，好比鉀、或氫氧化鉀，以及可樂瓶頸。我的了解不是可樂的蓋子，是它螺旋的頸部。這些混合好......

基本上就是按照步驟1-8，也可放入你自己的方式找到新的方法或新的結果。你放塑膠容器的空間(房間)也會決定塗層的均勻性。靠近牆壁那一面有一面的材料會比另一面塗得厚。#每樣東西都有場域，會直入你放塑膠盒的桌子，影響正在建立的塗層。

#記住安全第一！奈米塗層成功！

後記：
請大家埋頭實驗之餘，詳實紀錄你用的方法與結果。
因為這是新科學的最前線，充滿無限的新發現.....
#我這裡的奈米塗層法只是其中的方法之一，還有其他的方法。

https://www.facebook.com/permalink.php?story_fbid=391312037918753&id=100011198799032&hc_location=ufi

====
Thank you Mark House for sharing this this is a step-by-step procedure from Carolina Carolina De Roose
#KESHEHOWTOMAKENANOMATERIALS

Shared by Carolina De Roose

"HOW TO MAKE NANO MATERIALS: Wear protective suit (goggles, mask) try to avoid breathing vapors...once process is done do not handle the coated materials with bare hands...wear 2-3 layers of disposable rubber gloves...if you touch the nano material (use Ruta its a natural herb which you can buy in drops (*Rue Herb Tincture Ruta graveolens 100ml Dropper Bottle)

Step 1: Put rusty nails, chicken wire, wire (solid copper wire or wound fiber like wire) into plastic container.

Step 2: Add caustic (could be crystals, pellets, flakes, ammonia, sodium hydroxide, lye etc) (about a kilo of caustic you can produce about a half a ton of the right material) (add about 1/4 of a cup on the bottom of the plastic container).

Step 3: add boiling water (enough to submerge the materials by a half inch/inch or so (nails etc) because you need a heat generator (the boiling water). It's a boiling condition. It produces the right condition and environment to produce nano oxides.

Step 4: You have to close the "gap" the container (put the lid on) and leave for 24 hours minimum. The material needs time to do it's work. After 24 hours...empty the container. Do not touch the material much...you can drain the container...but the new container you put it in add a little bit of the caustic/water solution from the original contain. Put a little bit on the bottom of the new contain...It must be kept moist. You can use a different composition of container when you transfer it because it will give you different result for example if you put it in a glass container next instead of another plastic one. They recommend a plastic container because you get certain results with plastic.

Step 5: Transfer the materials you left in the 1st contain for at least 24 hours...into another contain which is electrically conductive (they use another plastic contain as stated above, with a little solution on the bottom to keep it very moist also as stated above then chicken wire folded over inside the contain to raise it like 1 inch off of the bottom...lay out the materials so they have their own space not touching one another...like how pizza's would be on a conveyor oven. (you could use a miniature metal plate/table instead of the chicken wire to hold it up off the bottom of the container)

Step 6: Add a very very small amount of voltage across the materials...he touches one piece of metal (old saw) and a nail at the same time (the nail and the saw piece aren't physically touching each other) with a voltage meter and banana clips (you could use a battery) It has to be of impulses of randomly between 5-10 seconds...then you withdraw the current/voltage.

Step 7: You put the cover back on the container (at this point it's container 2) and you leave it between 5-7 hours. Then you come back and create a small current again like before and then you leave it again for 5-7 hours you do this process 3 or 4 times over 24 hours. Even a small battery (as stated above) creates the right condition that allows the current to flow. This process allows nano layers to be produced from under to the top of the material. You create nano materials at near zero cost. Nano materials can be used for decontamination. This is a simple, and cheap method for producing nano materials that has been used for 7 years and is used for different purposes.

Step 8: The materials can then be moved into another container and must be keep with the lid on until point of use. So keep the container (number 3) closed with the newly created materials inside until you need to use them. * Secret, you can not expose the materials to air until the point of use...you have to prevent them from oxidizing further.
Any metal can be nano coated...be it steel, iron, copper, gold etc.

Copper sheets (like as thin as paper) with a copper oxide nano coating used in batteries...(worth a lot of $$) can be used as a super conductor and an insulator.

You got to remember that the metals you add to the "pot" (1st plastic container) will give you different composite layers....for instance lets say your first time through the process you add aluminum (or candle tins) these will dissolve in the solution and give you a composite layer. The composite layer will be determined by what metals are in the "pot". Verses no composite layers if you were strictly to use lets say just copper. Either way is fine...you will just get different results....in a way Mr. Keshe say's nano coating is like creating a magnet....and depending on your coatings you will attract different things.

You can repeat entire steps 1-8 several times to build up your layers...also adding "no salt" (a potassium substitute to salt found in your grocery store) or KOH (potassium hydroxide) and the tops of coke bottles (my understanding is it's not the caps but the "neck" and threaded part of the bottle) to the mix as well....basically follow steps 1-8 but also experiment and create detailed logs of all your experiments and perhaps you will discover a new way or new result. Also where in the room you place the plastic container will determine the homogenous of your layers...place it near a wall and half of your materials may be coated more heavily than the rest....everything has fields right down to the table you place it on....which can influence your layers you are creating Remember safety first! Good luck!

NOTES:
-We urge you not just to experiment but also log in detail your methods and results.

-That being said please experiment...as this is a new frontier in science and a near limitless amounts of new discoveries are possible...this is just one way to make nano materials....come up with other ways.

***Please remember to SHARE your KNOWLEDGE....lets keep this info and the discussion out in the open for all to learn and benefit from."